Router Lift RL1.0 "Made in Germany" for common European routers Product details:Quality made in Germany: construction made of high-quality aluminium and steel. Height fine adjustment to 1/10mm: extremely precise adjustment, with exact scaling and effective spindle lock, easily operated via hexagon socket screw. Smooth-running spindle columns: allow for continuous and exact fine height adjustment. Routing without rip fence: 2 drill holes for the rip fence pin enable free routing of e.g. round workpieces without rip fence. Easy mounting: mount the router to the RL1.0 using pre-drilled mounting holes (hole pattern in operating instructions). Absolutely flat: easy levelling of the RL1.0 by means of levelling screws in the insert plate. Laser scaling: millimeter scale on the surface for exact alignment of the rip fence. No need to drill your own holes: mounting holes (countersunk head) for quick router table installation are already pre-drilled. Technical data: Distance from the top edge of the inlay plate to the base plate of the mounted router: 14 mm (Routing depthloss) Dimension insert plate: 306 x 229 x 9 mm Corner radius of insert plate: 6 mm Height adjustment travel/rotation: 4 mm Height router lift (max. extended): 240mm Max. Adjustment travel: 111 mm Max. Cutter diameter: 86 mm (without insert ring) Weight: 4,5 kg Advantages and characteristics: Quality from Germany High quality, solid construction. Construction of high quality aluminium and steel. Fine height adjustment to 1/10mm Height fine adjustment extremely precise adjustable, with exact scaling and effective spindle lock, conveniently operated via hexagon socket screw. Smooth-running spindle columns Enable a stepless and exact fine height adjustment. Fits in (almost) every router table Robust, anodised aluminium insert plate The RL1.0 is compatible with a wide range of commercially available routers. All models can be found below. Assembly made easy Easy mounting of the router to the RL1.0 by means of pre-drilled mounting holes (drilling pattern in the operating instructions). Routing also without rip fence 2 holes for the fence pin allow you to freely route workpieces without rip fence (separate accessory). Absolutely flat Simple levelling of the RL1.0 by levelling screws in the insertion plate. Optionally a frame for a permanent level adjustment can be purchased. vNo drilling necessary Mounting holes (countersunk head) for quick Router Table installation are already pre-drilled. Lasered scaling Millimeter scaling on the surface for exact alignment of the rip fence. Directly compatible routers: Bosch: POF1200AE, POF1300, POF1400ACE Bosch: GOF1250CE/LCE, GMF1600CE, GOF1600CE Casals: CT2200VCE DeWalt: DW615, DW621, DW622, DW624, DW625 Elu: MOF96(E), MOF97(E), MOF131, MOF177(E), MOF 177/02 Type 2 Festool: OF1400 Freud: FT2000 (diabolo), FT2200VCE Mafell: LO 65 Ec Makita: RP1110 Perles: OF3-808(RE), OF9(E) Trend: T5, T10, T11 Würth: OF1100E Delivery Includes: 1x Router Lift RL1.0 2x insert rings 1x hexagon screwdriver 5x150 mm 4x fixing screws M6x50, washers and nuts 18x mounting screws for routers (various) 8x levelling screws M5x8 1x Protection plate 1x instruction manual 

Router lift with steel reduction plates 32 & 68 mmProduct details:Quality made in Germany: construction made of high-quality aluminium and steel. Height fine adjustment to 1/10mm: extremely precise adjustment, with exact scaling and effective spindle lock, easily operated via hexagon socket screw. Smooth-running spindle columns: allow for continuous and exact fine height adjustment. Routing without rip fence: 2 drill holes for the rip fence pin enable free routing of e.g. round workpieces without rip fence. Easy mounting: mount the router to the RL2.0 using pre-drilled mounting holes (hole pattern in operating instructions). Absolutely flat: easy levelling of the RL2.0 by means of levelling screws in the insert plate. Laser scaling: millimeter scale on the surface for exact alignment of the rip fence. No need to drill your own holes: mounting holes (countersunk head) for quick router table installation are already pre-drilled.Special feature of the 2nd generation:The magnetic reduction plates offer more choice and control in choosing the right hole size. Perfectly adapted to the size of the router cutter - especially for small workpieces, "getting stuck and stuck" at the edge of the hole is eliminated. Magnets for attaching additional accessories are distributed over the entire reduction plate. Additional recessed grip for easy changing of the reduction plates.Compatible Routers:Bosch: POF1200AE, POF1300, POF1400ACE , GOF1250CE/LCE, GMF1600CE, GOF1600CE Casals: CT2200VCE DeWalt: DW615, DW621, DW622, DW624, DW625 Elu: MOF96(E), MOF97(E), MOF131, MOF177(E), MOF 177/02 Type 2 Festool: OF1400 Freud: FT2000 (Diabolo), FT2200VCE Mafell: LO 65 EC Makita: RP1110 Perles: OF3-808(RE), OF9(E) Trend: T5, T10, T11 Würth: OF1100EExceptions: ELU MOF 96/02 (no tapped holes available), Festool OF2000, OF2200 and DeWalt DW626 (these are too large in the entire circumference and cannot be fitted into the lift construction).Technical Data:Dimension insert plate: 306 x 229 x 9 mm Corner radius of insert plate: 6 mm Distance from the top edge of the inlay plate to the base plate of the mounted router: 15 mm (loss of routing depth) Height adjustment travel/rotation: 4 mm Height router lift (max. extended): 240mm Max. cutter diameter: 86 mm Max. adjustment travel: 105 mm Weight: 4,5 kgDelivery includes:1x router lift RL2.0 2x reduction plates Ø 32 and 68 mm 1x hexagon screwdriver 5x150 mm 4x fixing screws M6x50, washers and nuts 18x mounting screws (various sizes) 8x levelling screws M5x8 1x instruction manual (german & english)

Router lift with steel reduction plates 32 & 68 mmProduct details:Quality made in Germany: construction made of high-quality aluminium and steel. Height fine adjustment to 1/10mm: extremely precise adjustment, with exact scaling and effective spindle lock, easily operated via hexagon socket screw. Smooth-running spindle columns: allow for continuous and exact fine height adjustment. Routing without rip fence: 2 drill holes for the rip fence pin enable free routing of e.g. round workpieces without rip fence. Easy mounting: mount the router to the RL2.0K using pre-drilled mounting holes (hole pattern in operating instructions). Absolutely flat: easy levelling of the RL2.0K by means of levelling screws in the insert plate. Laser scaling: millimeter scale on the surface for exact alignment of the rip fence. No need to drill your own holes: mounting holes (countersunk head) for quick router table installation are already pre-drilled.Special feature of the 2nd generation:The magnetic reduction plates offer more choice and control in choosing the right hole size. Perfectly adapted to the size of the router cutter - especially for small workpieces, "getting stuck and stuck" at the edge of the hole is eliminated. Magnets for attaching additional accessories are distributed over the entire reduction plate. Additional recessed grip for easy changing of the reduction plates.Compatible Routers:Bosch: POF1200AE, POF1300, POF1400ACE , GOF1250CE/LCE, GMF1600CE, GOF1600CE Casals: CT2200VCE DeWalt: DW615, DW621, DW622, DW624, DW625 Elu: MOF96(E), MOF97(E), MOF131, MOF177(E), MOF 177/02 Type 2 Festool: OF1400 Freud: FT2000 (Diabolo), FT2200VCE Mafell: LO 65 EC Makita: RP1110 Perles: OF3-808(RE), OF9(E) Trend: T5, T10, T11 Würth: OF1100EExceptions: ELU MOF 96/02 (no tapped holes available), Festool OF2000, OF2200 and DeWalt DW626 (these are too large in the entire circumference and cannot be fitted into the lift construction).Technical Data:Dimension insert plate: 298 x 235 x 9 mm Corner radius of insert plate: 6 mm Distance from the top edge of the inlay plate to the base plate of the mounted router: 15 mm (loss of routing depth) Height adjustment travel/rotation: 4 mm Height router lift (max. extended): 240mm Max. cutter diameter: 86 mm Max. adjustment travel: 105 mm Weight: 4,5 kgDelivery includes:1x router lift RL2.0 2x reduction plates Ø 32 and 68 mm 1x hexagon screwdriver 5x150 mm 4x fixing screws M6x50, washers and nuts 18x mounting screws (various sizes) 8x levelling screws M5x8 1x instruction manual (german & english)

Router lift (Kreg-format) with steel reduction plates 32 & 68 mmProduct details:Quality made in Germany: construction made of high-quality aluminium and steel.Height fine adjustment to 1/10mm: extremely precise adjustment, with exact scaling and effective spindle lock, easily operated via hexagon socket screw.Smooth-running spindle columns: allow for continuous and exact fine height adjustment.Routing without rip fence: 2 drill holes for the rip fence pin enable free routing of e.g. round workpieces without rip fence.Easy mounting: mounting of the router to the RL2.0-MINI through pre-drilled mounting holes (hole pattern in operating instructions).Absolutely flat: easy levelling of the RL2.0-MINI by means of levelling screws in the insert plate.Laser scaling: millimeter scale on the surface for exact alignment of the rip fence.No need to drill your own holes: mounting holes (countersunk head) for quick router table installation are already pre-drilled.Special features of the Mini-version:Compatible with the smallest routers.The reduction plates offer more choice and control in choosing the right hole size. Perfectly adapted to the size of the router - especially for small workpieces, "jamming and sticking" at the hole edge is eliminated.Magnets for fastening further accessories are distributed over the entire reduction plate.Additional recessed grip for easy changing of the reduction plates.Compatible routers:DeWalt: D26203, D26204 Festool: OF1010, OF1000, OF900E Makita: RT0700, RP0900 Metabo: OFE1229Technical data:Dimension insert plate: 298 x 235 x 9 mm Corner radius of insert plate: 19,05 mm (3/4")Distance from the top edge of the inlay plate to the base plate of the mounted router: 15 mm (loss of routing depth) Height adjustment travel/rotation: 4 mm Height router lift (max. extended): 240mm Max. cutter diameter: 86 mm Max. adjustment travel: 105 mm Weight: 4,5 kgDelivery Includes:1x router lift RL2.0K-MINI 2x reduction plates Ø 32 and 68 mm 1x hexagon screwdriver 5x150 mm 4x fixing screws M6x50, washers and nuts 18x mounting screws (various sizes) 8x levelling screws M5x8 1x instruction manual (german & english)

Router lift with steel reduction plates 32 & 68 mmProduct details:Quality made in Germany: construction made of high-quality aluminium and steel.Height fine adjustment to 1/10mm: extremely precise adjustment, with exact scaling and effective spindle lock, easily operated via hexagon socket screw.Smooth-running spindle columns: allow for continuous and exact fine height adjustment.Routing without rip fence: 2 drill holes for the rip fence pin enable free routing of e.g. round workpieces without rip fence.Easy mounting: mounting of the router to the RL2.0-MINI through pre-drilled mounting holes (hole pattern in operating instructions).Absolutely flat: easy levelling of the RL2.0-MINI by means of levelling screws in the insert plate.Laser scaling: millimeter scale on the surface for exact alignment of the rip fence.No need to drill your own holes: mounting holes (countersunk head) for quick router table installation are already pre-drilled.Special features of the Mini-version:Compatible with the smallest routers.The reduction plates offer more choice and control in choosing the right hole size. Perfectly adapted to the size of the router - especially for small workpieces, "jamming and sticking" at the hole edge is eliminated.Magnets for fastening further accessories are distributed over the entire reduction plate.Additional recessed grip for easy changing of the reduction plates.Compatible routers:DeWalt: D26203 Festool: OF1010, OF1000, OF900E Makita: RT0700, DRT50ZJX2 Technical data:Dimension insert plate: 306 x 229 x 9 mm Corner radius of insert plate: 6 mm Distance from the top edge of the inlay plate to the base plate of the mounted router: 15 mm (loss of routing depth) Height adjustment travel/rotation: 4 mm Height router lift (max. extended): 240mm Max. cutter diameter: 86 mm Max. adjustment travel: 105 mm Weight: 4,5 kgDelivery Includes:1x router lift RL2.0-MINI 2x reduction plates Ø 32 and 68 mm 1x hexagon screwdriver 5x150 mm 4x fixing screws M6x50, washers and nuts 18x mounting screws (various sizes) 8x levelling screws M5x8 1x instruction manual (german & english)

Router lift with magnetic steel reduction plates 16, 32 & 68 mmProduct details:Pivoting router lift from -5 degrees to 50 degrees - the first and only one of its kind! Quality made in Germany: construction made of high-quality aluminium and steel. For router motors with 43 mm clamping neck Classic snap-in guide points: 22.5°, 30°, 45° and 90° No loss of routing depth! Easy router bit changing, thanks to upward looking routing spindle and collet chuck Countless routing possibilities: grooves, rebates, chamfers, mitre cuts, and much more - and all this with only one slot routing cutter Height fine adjustment to 1/10mm: extremely precise adjustment, with exact scaling and effective spindle lock, conveniently operated via hexagon socket screw. Smooth-running spindle columns: allow continuous and exact fine height adjustment. Routing without rip fence: 2 drill holes for the rip fence pin enable free routing of e.g. round workpieces without rip fence. Absolutely flat: easy levelling of the RL3.0 using levelling screws in the insert plate. Laser scaling: millimetre scale on the surface for exact alignment of the rip fence.Easy to use:Height adjustment via rotary handle above Angle locking via a lever below Centering in the slotted hole by means of two levers below Additional recessed grip for easy changing of the reduction plates. Magnetism for attaching further accessories is distributed over the entire reduction plate. No own drillings necessary: mounting holes (countersunk head) for quick router table installation are already pre-drilled.Compatible router motors:Kress: 530 FM, 800 FME, 1050 FME Mafell: FM 800, FM 1000 Suhner: UAC 30 RF, UAD 25 RF, UAK 30 RF, UAL 23 RFNote: Not compatible with Trend T4EK.If your routing motor is not listed, please check the tolerances of the clamping neck specified by the manufacturer for your model or contact us. Technical data:Dimension insert plate: 306 x 229 x 9 mm Corner radius of insert plate: 6 mm Height adjustment per rotation: 4 mm Max. Adjustment travel: 101 mm Height router lift (max. extended): 240mm Max. Router bit diameter: 55 mm Weight: approx. 5 kg Delivery Includes:1x router lift OFL3.0 2x reduction plates slot hole Ø 16 and 32mm1x reduction plate round hole Ø 68 mm1x hexagon screwdriver 5x150 mm 4x fixing screws M6x50, washers and nuts 8x levelling screws M5x8 1x instruction manual

Router lift (Kreg-format) with magnetic steel reduction plates 16, 32 & 68 mmProduct details:Pivoting router lift from -5 degrees to 50 degrees - the first and only one of its kind! Quality made in Germany: construction made of high-quality aluminium and steel. For router motors with 43 mm clamping neck Classic snap-in guide points: 22.5°, 30°, 45° and 90° No loss of routing depth! Easy router bit changing, thanks to upward looking routing spindle and collet chuck Countless routing possibilities: grooves, rebates, chamfers, mitre cuts, and much more - and all this with only one slot routing cutter Height fine adjustment to 1/10mm: extremely precise adjustment, with exact scaling and effective spindle lock, conveniently operated via hexagon socket screw. Smooth-running spindle columns: allow continuous and exact fine height adjustment. Routing without rip fence: 2 drill holes for the rip fence pin enable free routing of e.g. round workpieces without rip fence. Absolutely flat: easy levelling of the RL3.0 using levelling screws in the insert plate. Laser scaling: millimetre scale on the surface for exact alignment of the rip fence.Easy to use:Height adjustment via rotary handle above Angle locking via a lever below Centering in the slotted hole by means of two levers below Additional recessed grip for easy changing of the reduction plates. Magnetism for attaching further accessories is distributed over the entire reduction plate. No own drillings necessary: mounting holes (countersunk head) for quick router table installation are already pre-drilled.Compatible router motors:Kress: 530 FM, 800 FME, 1050 FME Mafell: FM 800, FM 1000 Suhner: UAC 30 RF, UAD 25 RF, UAK 30 RF, UAL 23 RFNote: Not compatible with Trend T4EK.If your routing motor is not listed, please check the tolerances of the clamping neck specified by the manufacturer for your model or contact us. Technical data:Dimension insert plate: 298 x 235 x 243 mm Corner radius of insert plate: 6 mm Height adjustment per rotation: 4 mm Max. Adjustment travel: 101 mm Height router lift (max. extended): 240mm Max. Router bit diameter: 55 mm Weight: approx. 5 kg Delivery includes:1x router lift OFL3.0 2x reduction plates oblong hole Ø 16 and 32 1x reducing plate Ø 68 mm 1x hexagon screwdriver 5x150 mm 4x fixing screws M6x50, washers and nuts 8x levelling screws M5x8 1x instruction manual

Router lift adapter ML-A for milling motors. Converts your router table insert to a lift for router motors. Advantages and features: Quality from Germany Convenient height adjustment from above Suitable for router motors with Ø 43mm clamping neck with a maxinum power of 1100 Watt Efficient clamping from below Assembly made easy Direct compatible with: Insert Plate IP1.0 -TP Insert Plate IP2.0 -TP Trend CRT-MK3 router Table Trend WRT router table Technical Data: Max. router Ø: 50mm Ø cutter opening: 55mm Travel: 55mm Height adjustment from top with hexagon socket (5mm) Height adjustment travel per revolution: 1.5 mm Spindle locking underneath the table, locking on one side Dimensions (LxWxH): 158 x 106 x 136 mm Weight: approx. 1.6 kg Scope of delivery: 1x Sauter router lift adapter for router motors FML-A 1x set of mounting screws for attachment to the insertion plate

Router Lift ML-P The perfect entry into the MarMan Tool world of router lifts. For milling motors with Ø 43mm clamping neck | 306 x 229 x 9 mm. Advantages and features: Quality Made in Germany Convenient height adjustment from above Suitable for milling motors with Ø 43mm clamping neck with a maxinum power of 1100 Watt Efficient clamping from below Pre-assembled router motor lift adapter with insert plate Height adjustment from above Routing can be controlled via safety switch Easy mounting in the router table Including two reduction plates Ø 22 and 54 mm Technical Data: Max. router Ø: 50mm Ø cutter opening: 55mm Travel: 65mm Height adjustment from above with hexagon socket (5mm) Height adjustment travel per revolution: 1.5 mm Spindle locking underneath the table, locking on one side Dimensions of insert plate (LxWxH): 306 x 229 x 9 mm Corner radius of insertion plate: R6 Weight: approx. 2.9 kg Scope of delivery: 1x Router Lift ML-P 1x Set of fixing screws for installation in the router table 1x Reduction plates Ø 22 & 54 mm

Router Lift ML-BR Especially for milling motors with a 43mm neck The newly designed Router Lift for milling motors with Ø 43mm clamping neck is the successor of our popular RL2.0-AD43. With its new "bridge" design, it is perfectly tailored to the use of large and powerful router motors. The ML-BR is the only router lift with an integrated extraction connection that efficiently extracts wood chips and saw dust.  Like all other MarMan Tools router lifts, the ML-BR is characterized by first-class and solid workmanship. Advantages and features: New "Bridge" design for comfortable and reliable mounting of the router motor Suitable for all router motors with Ø 43mm clamping neck Easy height adjustment and spindle lock from above Routing can be controlled via safety switch Easy cutter changes from above thanks to exposed and very easily accessible cutter spindle No loss of milling depth Fine height adjustment can be set to within 1/10 mm High-contrast laser scaling Assembly made easy Integrated extraction connetionQuality 100% Made in Deutschland Technical Data: Max. router Ø: 55mm Ø cutter opening: 98mm Travel: 90mm Height adjustment from top with hexagon socket (5mm) Adjustment travel per revolution: 2mm Spindle lock from above with hexagon socket (5mm) Dimensions of insert plate: 306 x 229 x 9 mm Corner radius of insert plate: R6 Dimensions (LxWxH): 306 x 229 x 213 mm Weight: approx. 4,0 kg Scope of delivery: 1x Router Lift ML-BR 1x reduction plates Ø 32 & 68 mm 1x set of fastening screws for installation in the router table

Router Lift ML-BR-K (KREG-format) Especially for milling motors with a 43mm neck The newly designed Router Lift for milling motors with Ø 43mm clamping neck is the successor of our popular RL2.0-AD43. With its new "bridge" design, it is perfectly tailored to the use of large and powerful router motors. The ML-BR is the only router lift with an integrated extraction connection that efficiently extracts wood chips and saw dust.  Like all other MarMan Tools router lifts, the ML-BR is characterized by first-class and solid workmanship. Advantages and features: New "Bridge" design for comfortable and reliable mounting of the router motor Suitable for all router motors with Ø 43mm clamping neck Easy height adjustment and spindle lock from above Routing can be controlled via safety switch Easy cutter changes from above thanks to exposed and very easily accessible cutter spindle No loss of milling depth Fine height adjustment can be set to within 1/10 mm High-contrast laser scaling Assembly made easy Integrated extraction connetionQuality 100% Made in Deutschland Technical Data: Max. router Ø: 55mm Ø cutter opening: 98mm Travel: 90mm Height adjustment from top with hexagon socket (5mm) Adjustment travel per revolution: 2mm Spindle lock from above with hexagon socket (5mm) Dimensions of insert plate: 298 x 235 x 9 mm Corner radius of insert plate: 19,05 mm (3/4") Dimensions (LxWxH): 298 x 235 x 213 mm Weight: approx. 4,0 kg Scope of delivery: 1x Router Lift ML-BR 1x reduction plates Ø 32 & 68 mm 1x set of fastening screws for installation in the router table

Router Lift ML-P-K (Kreg-format) The perfect entry into the MarMan Tool world of router lifts. For milling motors with Ø 43mm clamping neck |  298 x 235 x 9 mm. Advantages and features: Quality Made in Germany Convenient height adjustment from above Suitable for milling motors with Ø 43mm clamping neck with a maxinum power of 1100 Watt Efficient clamping from below Pre-assembled router motor lift adapter with insert plate Height adjustment from above Routing can be controlled via safety switch Easy mounting in the router table Including two reduction plates Ø 22 and 54 mm Technical Data: Max. router Ø: 50mm Ø cutter opening: 55mm Travel: 65mm Height adjustment from above with hexagon socket (5mm) Height adjustment travel per revolution: 1.5 mm Spindle locking underneath the table, locking on one side Dimensions of insert plate (LxWxH): 298 x 235 x 9 mm Corner radius of insertion plate: 19,05 mm (3/4") Weight: approx. 2.9 kg Scope of delivery: 1x Router Lift ML-P-K 1x Set of fixing screws for installation in the router table 1x Reduction plates Ø 22 & 54 mm

Reduction plate long shape for router lift RL3.0 Product details :Made of galvanised 2 mm thick steel Ø Cutter opening: 22 mm Length of the oblong hole: 60 mmDelivery includes:1x reduction plate RP3.0-22

Reduction plate for insert plate IP2.0 and router lift RL 2.0 and 3.0Product details:Made of galvanised 2 mm thick steel Ø Cutter opening: undrilled (for self-drilling or closing the table top)Delivery Includes:1x reduction plate undrilled

Reduction plate round hole for insert plate IP2.0 and router lift RL2.0 & RL3.0 Product details: Made of galvanised 2 mm thick steel Ø Cutter opening: 32 mmDelivery includes:1x reduction plate RP2.0-32

Reduction plate round hole for insert plate IP2.0 and router lift RL2.0 & RL3.0Product details: Made of galvanised 2 mm thick steel Ø Cutter opening: 98 mmDelivery includes:1x reduction plate RP2.0-98

Reduction plate round hole for insert plate IP2.0 and router lift RL2.0 & RL3.0 Product details: Made of galvanised 2 mm thick steel Ø Cutter opening: 68 mmDelivery includes:1x reduction plate RP2.0-68

Reduction plate long shape for router lift RL3.0Product details:Made of galvanised 2 mm thick steel Ø Cutter opening: 54 mm Length of the oblong hole: 76 mmDelivery includes:1x reduction plate RP3.0-54

Reduction plate long shape for router lift RL3.0Product details:Made of galvanised 2 mm thick steel Ø Cutter opening: 68 mm Length of the oblong hole: 82 mmDelivery Includes:1x reduction plate RP3.0-68

Reduction plate round hole for insert plate IP2.0 and router lift RL2.0 & RL3.0 Product details: Made of galvanised 2 mm thick steel Ø Cutter opening: 54 mmDelivery includes:1x reduction plate RP2.0-54

Reduction plate round hole for insert plate IP2.0 and router lift RL2.0 & RL3.0 Product details: Made of galvanised 2 mm thick steel Ø Cutter opening: 10 mmDelivery includes:1x reduction plate RP2.0-10

Reduction plate round hole for insert plate IP2.0 and router lift RL2.0 & RL3.0 Product details: Made of galvanised 2 mm thick steel Ø Cutter opening: 86 mmDelivery includes:1x reduction plate RP2.0-86

Reduction plate long shape for router lift RL3.0Product details:Made of galvanised 2 mm thick steel Ø Cutter opening: 32 mm length of the oblong hole: 64 mmDelivery includes:1x reduction plate RP3.0-32

Reduction plate long shape for router lift RL3.0 Product details: Made of galvanised 2 mm thick steel Ø Cutter opening: 12 mm Length of the oblong hole: 54 mmDelivery includes:1x reduction plate RP3.0-12